21ic问答首页 - RTC闹钟的中断

RTC闹钟的中断

yinxiangh2020-09-09

有关RTC闹钟的中断,就是要求每一个小时整点产生一次RTC闹钟中断,前几个小时正常,可后面就不产生RTC中断,各位指点下.

回答 +关注 16

1103人浏览 8人回答问题举报

8 个回答

赞0

yinxiangh

唉，还是没有什么结果，算了，多谢大家啦

评论

2020-09-09

分享没有帮助举报
赞0

dingy

程序跑飞了有可能是数据类型的问题

评论

2020-09-09

分享没有帮助举报
赞0

tian111

估计是程序哪里跑丢了

评论

2020-09-09

分享没有帮助举报
赞0

zhouyong77

应该还是中断配置没对

评论

2020-09-09

分享没有帮助举报
赞0

yinxiangh

给你看下,void NVIC_Configuration(void)
{
      NVIC_InitTypeDef NVIC_InitStructure;
      EXTI_InitTypeDef EXTI_InitStructure;

      /* Set the Vector Table base location at 0x08000000 */
      NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);

      /* 2 bit for pre-emption priority, 2 bits for subpriority */
      NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0);
      //------RTC闹钟-------------------------------------------------------
      NVIC_InitStructure.NVIC_IRQChannel = RTC_Alarm_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      EXTI_InitStructure.EXTI_Line = EXTI_Line17;
      EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
      EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
      EXTI_InitStructure.EXTI_LineCmd = ENABLE;
      EXTI_Init(&EXTI_InitStructure);

      // 键盘
      NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);
   //蓝牙
      NVIC_InitStructure.NVIC_IRQChannel = BLE_INT_EXTI_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);
      //恢复出厂按键
      NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

#if WATCHDOG_ENABLE
      NVIC_InitStructure.NVIC_IRQChannel = WWDG_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 4;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);
#endif

      //------TIM6-------------------------------------------------------
      NVIC_InitStructure.NVIC_IRQChannel = TIM6_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 5;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      #if LOCK_WITH_FINGERPRINT
      // 指纹
      NVIC_InitStructure.NVIC_IRQChannel = FP_MODULE_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 6;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);
   #endif

      //------TIM4读卡-------------------------------------------------------
      NVIC_InitStructure.NVIC_IRQChannel = TIM4_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 7;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      //------TIM3-------------------------------------------------------
      NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 8;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      // console串口
      NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 9;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 10;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      NVIC_InitStructure.NVIC_IRQChannel = EXTI3_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 11;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);

      NVIC_InitStructure.NVIC_IRQChannel = EXTI4_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority = 12;
      NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
      NVIC_Init(&NVIC_InitStructure);void RTC_Alarm_IRQHandler(void)
{
      keylock_t * keylock=Keylock_Msg_Accept();

      RFID_ChkCard_Disable();
      if (RTC_GetITStatus(RTC_IT_ALRA) != RESET)
      {
            RTC_ClearITPendingBit(RTC_IT_ALRA);
            EXTI_ClearITPendingBit(EXTI_Line17);
            //System_Sleep_Disable();
            IntWakeupSce.Sys_sync_flag= SYNC_RECYCLE;
            }
      if (RTC_GetITStatus(RTC_IT_ALRB) != RESET)
      {
            RTC_ClearITPendingBit(RTC_IT_ALRB);
            EXTI_ClearITPendingBit(EXTI_Line17);
            if (keylock->lockedflag == TRUE)
            {
                     IntWakeupSce.lockedrelease = TRUE;
                     }
            }
      #ifdef CHECK_WAKEUP_MODE
            wakeup_mode |= WAKEUP_BY_RTC;
      #endif

void RTC_RandomPwUpdate_Alarm(void)
{
      RTC_TimeTypeDef  RTC_TimeStruct;
      RTC_AlarmTypeDef RTC_AlarmStruct;

      APP_TRACE_DBG("%s %d\n", __FUNCTION__, __LINE__);
         RTC_GetTime(RTC_Format_BIN, &RTC_TimeStruct);
      RTCTime_AddCalculate(1, CALCULATE_HOUR, &RTC_TimeStruct);

      /* Allow access to BKP Domain */
      PWR_RTCAccessCmd(ENABLE);
      RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
      RTC_AlarmStruct.RTC_AlarmTime.RTC_H12 = RTC_TimeStruct.RTC_H12;
      RTC_AlarmStruct.RTC_AlarmTime.RTC_Hours = RTC_TimeStruct.RTC_Hours;
RTC_AlarmStruct.RTC_AlarmTime.RTC_Minutes = (RTC_TimeStruct.RTC_Minutes + 10) % 60;
RTC_AlarmStruct.RTC_AlarmTime.RTC_Seconds = 0;
      RTC_AlarmStruct.RTC_AlarmDateWeekDay = 0x31;
      RTC_AlarmStruct.RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date;
      RTC_AlarmStruct.RTC_AlarmMask = RTC_AlarmMask_DateWeekDay| RTC_AlarmMask_Hours;
      RTC_SetAlarm(RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStruct);
      RTC_WaitForSynchro();
      RTC_ClearFlag(RTC_FLAG_ALRAF);
      EXTI_ClearITPendingBit(EXTI_Line17);
      RTC_ITConfig(RTC_IT_ALRA, ENABLE);
      RTC_AlarmCmd(RTC_Alarm_A, ENABLE);

我这里改成10分钟一次.
本来我要的是1个小时一次中断

评论

2020-09-09

分享没有帮助举报
赞0

zhuww

楼上好建议，毕竟中断次数太少，每次中断处理结束后再执行一次初始化还是可以的。防止配置失效。

评论

2020-09-09

分享没有帮助举报
赞0

yufe

你这样每次中断后，你重新初始化一次这个配置。

评论

2020-09-09

分享没有帮助举报
赞0

zyf部长

肯定是处理中断处理的不对了。

评论

2020-09-09

分享没有帮助举报