21ic问答首页 - STM32F4驱动OV5640卡在EV6

STM32F4驱动OV5640卡在EV6 赏100家园币

feiyinglala2022-10-14

本帖最后由 feiyinglala 于 2022-10-14 19:27 编辑

使用STM32F429驱动OV5640模块，在使用硬件I2C（PB8 PB9）驱动，始终无法正常读写，OV5640地址配置为0x78
现象：总线可以正常启动，但发送完从设备地址后，立马卡住,在EV6中无法跳过
I2C1读取OV5640代码如下：

/**
* @brief 从 OV5640 寄存器中读取一个字节的数据
* @param Addr: 寄存器地址
* @retval 返回读取得的数据
*/
u8 OV5640_ReadReg(uint16_t Addr)
{
uint32_t timeout = DCMI_TIMEOUT_MAX;
uint8_t Data = 0;
while(I2C_GetFlagStatus(CAMERA_I2C, I2C_FLAG_BUSY))
if((timeout--) == 0) return 0xFF;
//1.开始【发送】--* Generate the Start Condition *
I2C_GenerateSTART(CAMERA_I2C, ENABLE); //启动I2C STM32进入主模式标志：SR1->SB 0-1
//----* Test on CAMERA_I2C EV5 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_MODE_SELECT))
{ //----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//2.发送从设备地址 - 主发送--* Send DCMI selcted device slave Address for write *
I2C_Send7bitAddress(CAMERA_I2C, OV5640_DEVICE_ADDRESS, I2C_Direction_Transmitter); //启动I2C STM32发送从地址标志：SR1->ADDR 0-1 【一直收不到】//执行完此句后,EV5结束，DR被赋值，SB1被重置
//20220922 受https://shequ.stmicroelectronics.cn/forum.php?mod=viewthread&tid=602816启发，需排查此步后，EV5对应的A如何检测？标志是啥
//----* Test on I2C1 EV6 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED))
{//----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF; //[卡在这行，读取ID时
}
//3.1 发送寄存器地址--* Send I2C1 location address MSB *
I2C_SendData( CAMERA_I2C, (uint8_t)((Addr>>8) & 0xFF) ); //【存疑】是否分2次发？？？
//----* Test on I2C1 EV8 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
{ //----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//----* Clear AF flag if arised *
CAMERA_I2C->SR1 |= (uint16_t)0x0400;
//3.2 发送寄存器地址--* Send I2C1 location address LSB *
I2C_SendData( CAMERA_I2C, (uint8_t)(Addr & 0xFF) );
//----* Test on I2C1 EV8 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
{ //----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//----* Clear AF flag if arised *
CAMERA_I2C->SR1 |= (uint16_t)0x0400;
//4.开始【接收】--* Generate the Start Condition *
I2C_GenerateSTART(CAMERA_I2C, ENABLE);
//----* Test on I2C1 EV6 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_MODE_SELECT))
{ //----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//5.发送从设备地址 - 主接收,读取命令--* Send DCMI selcted device slave Address for write *
I2C_Send7bitAddress(CAMERA_I2C, OV5640_DEVICE_ADDRESS, I2C_Direction_Receiver);
//----* Test on I2C1 EV6 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED))
{ //----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//----* Prepare an NACK for the next data received *
I2C_AcknowledgeConfig(CAMERA_I2C, DISABLE);
//----* Test on I2C1 EV7 and clear it *
timeout = DCMI_TIMEOUT_MAX; //----* Initialize timeout value *
while (!I2C_CheckEvent(CAMERA_I2C, I2C_EVENT_MASTER_BYTE_RECEIVED))
{
//----* If the timeout delay is exeeded, exit with error code *
if ((timeout--) == 0) return 0xFF;
}
//----* Prepare Stop after receiving data *
I2C_GenerateSTOP(CAMERA_I2C, ENABLE);
//----* Receive the Data *
Data = I2C_ReceiveData(CAMERA_I2C);
//----* return the read data *
return Data;
}

我被这个问题困扰很久了，我特意还用I2C2驱动MPU6050 QMC5883两个模块都可以正常驱动。
我把I2C1(OV5640) I2C2(MPU6050 QMC5883)在EV6验证时的截图如下：
这是I2C1的，有问题的

这是I2C2的，正常运行的

回答 +关注 15

24368人浏览 4人回答问题举报

4 个回答

赞0

Stahan

摄像头时钟没打开

评论

2022-11-11

分享没有帮助举报
赞0

Innercourage

需要添加库文件

评论

2022-11-08

分享没有帮助举报
赞0

feiyinglala

经调试，原来是因为OV5640的XCLK未输入时钟，所以摄像头处于停工状态，我把TIM1-CH2的PWM输出到XCLK就好了
XCLK对应PA8引脚，配置如下
//-----***PA8作为TIM1-ch2输出PWM到XCLK引脚***
GPIO_InitStructure.GPIO_Pin = MCO_XCLK_GPIO_PIN ;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(MCO_XCLK_GPIO_PORT, &GPIO_InitStructure);
GPIO_ResetBits(MCO_XCLK_GPIO_PORT,MCO_XCLK_GPIO_PIN);
GPIO_PinAFConfig(MCO_XCLK_GPIO_PORT, MCO_XCLK_PINSOURCE, GPIO_AF_TIM1);//MCO_XCLK_AF); //¸´ÓÃ
//RCC_MCO1Config(RCC_MCO1Source_PLLCLK, RCC_MCO1Div_1); //Ê¹ÄÜMCOÊ±ÖÓ
TIM1_Config();

评论

2022-10-16

分享没有帮助举报
赞0

feiyinglala

本帖最后由 feiyinglala 于 2022-10-14 19:28 编辑

我跳过所有的校验，读到的是0x79(最后发送的地址留存在I2C1的DR寄存器)中

评论

2022-10-14

分享没有帮助举报