日志
模拟IIC静默模式
|||
/**--------------文件信息--------------------------------------------------------------
** 文 件 名: IIC_Recv.h
** 创 建 人: WEN (wenshijian4@163.com,QQ214490357)
** 创建日期: 2015年9月16日
** 描 述: IIC靜默模式下，接收所有IIC數據，并轉發到串口;只读IIC数据
**---------- 版本信息------------------------------------------------------------------
** 版 本: V2.92
** 说 明: IIC_Recv.lib的头文件,请首先下载IIC_Recv.lib
**-------------------------------------------------------------------------------------
**************************************************************************************/
/**************************************************************************************
//請根據以下4個步驟，在程序對應位置修改IO口的配置以及中斷！！
//1.定義SCL,SDA,INT
#define PA4_SDA GPIO_Pin_4
#define PA5_INT GPIO_Pin_5
#define PA6_SCL GPIO_Pin_6
//---以下三個宏定義需要根據不同的硬件來修改，但是名字不能修改
#define Read_SDA GPIO_ReadInputDataBit(GPIOA, PA4_SDA)
#define Read_INT GPIO_ReadInputDataBit(GPIOA, PA5_INT)
#define Read_SCL GPIO_ReadInputDataBit(GPIOA, PA6_SCL)
//---注意：Read_SDA、Read_INT、Read_SCL爲關鍵字，不能改變，否則出錯！！！！
//2.三個引脚都必須定義爲IPU，根據硬件修改
GPIO_InitStructure.GPIO_Pin = PA4_SDA|PA5_INT|PA6_SCL;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//3.必須使能INT中斷，上下邊沿 ，根據硬件修改
GPIO_EXTILineConfig(GPIO_PortSourceGPIOA, GPIO_PinSource5);
EXTI_ClearITPendingBit(EXTI_Line5);
EXTI_InitStructure.EXTI_Line = EXTI_Line5;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
EXTI_InitStructure.EXTI_LineCmd =ENABLE;
EXTI_Init(&EXTI_InitStructure);
//4.開啓中斷，根據硬件修改
NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority= 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
***************************************************************************************/
#include "app_cfg.h"
/**************************************************************************************
** 函数名称: IIC_ReadData
** 功能描述: 读取IIC数据，并返回数据长度及数据内容
** 参 数: *IIC_Recv :指向用于接收IIC数据的数组，
** 返 回 值: 接收到的数据长度(以字节为单位)
** 日 期: 2015年4月17日
**-------------------------------------------------------------------------------------
** 調用方式:
** 説 明:
**-------------------------------------------------------------------------------------
***************************************************************************************/
unsigned int IIC_ReadData(unsigned char *IIC_Recv);
/**************************************************************************************
//代碼調用過程 實例
unsigned int IIC_DataLens;
unsigned char IIC_Data[100];//這個數組應該定義大點，怕溢出 應該>50
void EXTI9_5_IRQHandler(void)
{
//根據上升沿、下降沿來判斷是否讀IIC數據
if(EXTI_GetITStatus(EXTI_Line5) != RESET)
{
EXTI_ClearITPendingBit(EXTI_Line5);
if(Read_INT) //INT上升沿，則把數據通過串口發出
{
UARTSd_Arr(USART1,IIC_Data,IIC_DataLens);
IIC_DataLens=0;
}
else //INT下降沿，准备接收数据
{
IIC_DataLens=IIC_ReadData(IIC_Data);
}
}
}
********************************IIC_Recv.h文件结束*************************************/
/*----------------------------------IIC数据分析 IIC静音模式----------------------------
IIC数据定义：
B8:物理地址+写
B9:物理地址+读
B8 20 B9 X1 Y1 X2 Y2 00 00 00 00
| | | |第二触摸点Y坐标
| | |第二触摸点X坐标
| |第一触摸点Y坐标
|第一触摸点X坐标
1.每次触摸最少三个数据，与触摸屏接触时间越长，则发出的数据越多；
2.触摸弹起：坐标全为0；
3.各类手势：发出手势经过的X,Y坐标点；
4.所有帧间隔：32ms;
5.忽略ACK/NAK.
----------------------电容屏IIC触摸数据-------------------------
B8 20 B9 F6 13 00 00 00 00 00 00 //单点触摸 短按，约0.4S
B8 20 B9 F6 13 00 00 00 00 00 00 //间隔32ms
B8 20 B9 F6 13 00 00 00 00 00 00
B8 20 B9 F6 13 00 00 00 00 00 00
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
B8 20 B9 AE 5D 00 00 00 00 00 00 //单点触摸 长按约1S
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
B8 20 B9 07 02 00 00 00 00 00 00 //单点触摸 快速短按，约0.1S，最短
B8 20 B9 07 02 00 00 00 00 00 00 //间隔32ms
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
B8 20 B9 BB 85 00 00 00 00 00 00 //两点触摸
B8 20 B9 BB 85 A0 3B 00 00 00 00 //两点触摸
B8 20 B9 BB 85 A0 3B 00 00 00 00
B8 20 B9 BB 85 A0 3B 00 00 00 00
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
B8 20 B9 C1 4D 00 00 00 00 00 00 //单点手势
B8 20 B9 C1 4D 00 00 00 00 00 00
B8 20 B9 C1 4D 00 00 00 00 00 00
B8 20 B9 B8 54 00 00 00 00 00 00
B8 20 B9 AE 5D 00 00 00 00 00 00
B8 20 B9 A6 67 00 00 00 00 00 00
B8 20 B9 9C 73 00 00 00 00 00 00
B8 20 B9 92 7C 00 00 00 00 00 00
B8 20 B9 89 85 00 00 00 00 00 00
B8 20 B9 81 8C 00 00 00 00 00 00
B8 20 B9 7B 91 00 00 00 00 00 00
B8 20 B9 78 95 00 00 00 00 00 00
B8 20 B9 77 96 00 00 00 00 00 00
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
B8 20 B9 E3 69 00 00 00 00 00 00 //两点手势
B8 20 B9 E3 69 D2 2E 00 00 00 00 //两点手势
B8 20 B9 E3 69 D2 2E 00 00 00 00
B8 20 B9 E3 69 D2 2E 00 00 00 00
B8 20 B9 E3 69 D2 2E 00 00 00 00
B8 20 B9 DA 72 CA 35 00 00 00 00
B8 20 B9 D5 78 C5 3A 00 00 00 00
B8 20 B9 CF 7E C0 3F 00 00 00 00
B8 20 B9 C8 83 BB 44 00 00 00 00
B8 20 B9 C2 88 B4 49 00 00 00 00
B8 20 B9 BB 8D AD 4E 00 00 00 00
B8 20 B9 B4 92 A6 52 00 00 00 00
B8 20 B9 AD 97 A0 57 00 00 00 00
B8 20 B9 A6 9D 99 5B 00 00 00 00
B8 20 B9 9F A2 92 60 00 00 00 00
B8 20 B9 98 A7 8C 65 00 00 00 00
B8 20 B9 91 AC 86 69 00 00 00 00
B8 20 B9 8A AF 7E 6D 00 00 00 00
B8 20 B9 83 B3 78 71 00 00 00 00
B8 20 B9 7D B7 72 74 00 00 00 00
B8 20 B9 7A B9 6E 77 00 00 00 00
B8 20 B9 77 BB 6B 79 00 00 00 00
B8 20 B9 00 00 00 00 00 00 00 00 //弹起
-------------------------------------------------------------------------------------*/
